Eliminate hot second-floor rooms, clammy indoor humidity, and inflated electric bills. We engineer split-system central air conditioning installations tailored to the specific architectural demands of Westmoreland County homes. Designed through rigorous ACCA Manual J load calculations, installed with nitrogen-purged brazing, and commissioned to laboratory-grade psychrometric standards.
Serving Greensburg, Fort Allen, Saybrook Village, Academy Hill, Carbon & all Westmoreland County communities.
Over 75% of residential cooling performance issues originate from rushed, improper installation practices. We execute an uncompromising 8-stage mechanical protocol that guarantees peak efficiency, silent operation, and a full 15 to 20-year equipment lifespan.
We model your home structure using computer software: measuring wall construction, insulation levels, window orientation relative to afternoon sun, infiltration, and internal heat loads to determine exact BTU cooling demand.
We select an AHRI-certified equipment combination matching outdoor condenser, indoor evaporator coil, and furnace blower. This verified match ensures advertised SEER2 efficiency, rebate eligibility, and warranty validity.
We custom-fabricate galvanized steel transition fittings and radius turning vanes in our shop. This guarantees smooth, low-friction airflow between your existing furnace cabinet and the new cased evaporator coil.
The condensing unit is set on a thick composite equipment pad with neoprene vibration isolation pads. We maintain a minimum 24-inch perimeter clearance and install an outdoor weather-rated electrical disconnect.
While brazing copper linesets with 15% silver alloy, we continuously sweep dry nitrogen at 3 to 5 PSI through the tubing. This completely eliminates internal copper oxide flaking that ruins TXVs and compressor bearings.
We pull a deep vacuum below 500 microns with a two-stage commercial pump and verify moisture elimination with a digital micron gauge during a 15-minute standing decay test before releasing chemical refrigerant.
We install a primary PVC drain line with cleanout tee, an emergency secondary drain pan for attic and finished basement installations, and a magnetic Safe-T-Switch float sensor that shuts down the system if water ever backs up.
We charge refrigerant by digital scale, measure liquid subcooling to factory target (8°F to 12°F for TXV), verify total duct static pressure (TESP), and confirm a healthy 16°F to 21°F temperature drop (Delta-T) across the coil.
Many HVAC installers pack up their tools the instant cold air starts blowing from supply registers. We subject every newly installed central split cooling system to a rigorous 45-minute dynamic psychrometric test after steady-state operating pressures have stabilized.
We insert calibrated dual digital psychrometers into the return air plenum directly before the filter and into the supply air plenum 12 inches downstream of the evaporator coil. Under standard Pennsylvania indoor summer conditions (75°F dry-bulb, 50% relative humidity), a properly charged, properly flowing system must produce a temperature drop of 16°F to 21°F.
By measuring both dry-bulb temperature and wet-bulb humidity, our digital instruments calculate total air enthalpy change across the coil. This quantifies exact latent BTUs removed, verifying that the air conditioner is extracting moisture at design capacity rather than simply recirculating humid, chilled air.
We measure total external static pressure (TESP) between supply and return trunks with a dual-port digital manometer. If resistance exceeds 0.50 in. w.c., our technicians fine-tune blower speed taps or adjust duct balancing dampers before handing over your completed commissioning report.
In Greensburg, traditional HVAC contractors frequently guess cooling tonnage by dividing total square footage by 500. A 2,000-square-foot home is arbitrarily given a 4-ton air conditioner. This dangerous practice leads to severe equipment short-cycling, high summer humidity, and bloated electric bills.
Modern building science proves that window orientation, shading from Western Pennsylvania trees, insulation depth, and ceiling height dramatically alter cooling loads. Two identical 2,000 sq ft homes in Greensburg can have cooling requirements varying from 2.5 tons to 3.5 tons depending on architectural thermal resistance.
We guarantee that your newly installed central air conditioning system will satisfy both sensible heat loads (chilling room temperature) and latent moisture loads (wringing out Pennsylvania humidity) without short-cycling or freezing coils.
| Engineering Factor | 500 Sq Ft Rule (Amateur) | Wrightsoft Manual J (Our Standard) |
|---|---|---|
| Calculated Metrics | Floor area only | Walls, ceilings, windows, air infiltration, sun angles |
| Humidity Control | Poor (Runs 8-10 min; leaves air sticky) | Optimal (Runs full cycle to condense gallons of water) |
| Compressor Cycling | Frequent short-cycles (6-10x per hour) | Balanced, steady cycles (2-3x per hour) |
| Equipment Lifespan | Premature death in 8-10 years | Extended lifespan of 15-20+ years |
| Electric Utility Bills | High starting inrush spike costs | Low steady-state energy consumption |
Many homes in Greensburg already have a natural gas furnace providing winter heat through ductwork. Adding a central split air conditioner is an efficient, cost-effective upgrade that leverages your existing heating blower and supply ductwork.
We mount a heavy-duty cased A-coil or N-coil directly on top of your existing furnace warm-air supply opening. We fabricate custom galvanized sheet metal transition collars to ensure an airtight, aerodynamic seal with zero air leakage.
We core-drill a clean penetration through your basement rim joist, route insulated copper suction and liquid lines along ceiling joists, and mount the condensing unit outdoors on a composite pad clear of landscaping and roof drip lines.
We install a dedicated 240V circuit breaker in your electrical panel, wire a weatherproof outdoor disconnect with surge suppression, and run low-voltage thermostat wiring with a continuous 24V common wire (C-wire) to power smart thermostats.
When adding central air conditioning to an existing Greensburg furnace, the furnace blower motor must move exactly 350 to 400 CFM (cubic feet per minute) of air per ton of cooling capacity across the newly installed evaporator coil. Older permanent split capacitor (PSC) blower motors deliver fixed airflow that drops precipitously when static pressure increases, risking frozen evaporator coils and poor dehumidification.
If your existing furnace features a traditional PSC motor, our installation technicians measure high-voltage blower winding taps and adjust cooling speed settings from Medium-Low to High. We measure total external static pressure with a digital dual-port manometer to confirm the blower overcomes the added 0.20 to 0.30 in. w.c. resistance of the new cased evaporator coil without overheating motor windings.
For homes requiring superior humidity extraction, we offer drop-in electronically commutated motor (ECM) upgrades. Smart ECM blowers automatically ramp up rotational torque to maintain constant programmed CFM airflow even as air filters load with dust, consuming up to 60% less electrical wattage than older induction motors and enabling whisper-quiet continuous circulation.
When contractors braze copper pipes without flowing dry nitrogen, high temperatures react with room oxygen to create black cupric oxide scale. This abrasive particulate washes through the refrigerant, clogging TXV metering screens and destroying compressor scroll bearings within 3 to 5 years.
Simultaneously, pulling a deep vacuum down to 500 microns boils away microscopic moisture inside the tubing. Moisture reacts with modern POE synthetic compressor oils to form destructive hydrofluoric acids. Our 15-minute standing decay test ensures absolute chemical purity and hermetic integrity.
Forms black cupric oxide scale inside lineset. Sludge clogs TXV screen, causing erratic subcooling, oil breakdown, and premature compressor burnout.
Displaces all internal oxygen during brazing. Interior walls remain completely mirror-bright and clean, ensuring unobstructed refrigerant flow and long compressor life.
Technician pumps down for only 10 minutes using mechanical manifold gauges. Leaves water vapor inside lines, forming acid that eats motor winding varnish.
Boils all moisture away at room temperature; 15-minute decay test guarantees zero leaks and pristine chemical dryness before opening factory service valves.
A central air conditioning split system relies on chemical refrigerant not only to carry thermal heat, but also to carry synthetic polyolester (POE) lubricant back to the compressor crankcase. If linesets are improperly sized or pitched, lubricating oil pools in low spots, starving compressor bearings and causing catastrophic mechanical seizure.
Vapor lines must maintain minimum gas velocities of 1,000 to 1,200 feet per minute in horizontal runs and 1,500 feet per minute in vertical risers to entrain and push heavy lubricating oil uphill back to the outdoor compressor.
Where outdoor condensing units are installed significantly above the indoor evaporator coil (such as grade-level units serving walk-out basements), we braze engineered inverted oil traps at 15 to 20-foot riser intervals to ensure continuous oil return.
We size the 3/8-inch high-pressure liquid line with precision to prevent excessive friction pressure drops. Avoiding liquid line pressure drop ensures subcooled liquid refrigerant reaches the TXV inlet without vaporizing into premature flash gas bubbles.
We offer three distinct tiers of residential central air conditioning split systems to suit your family comfort preferences, home architectural design, and energy savings goals.
13.4 - 14.3 SEER2 Single-Stage
Dependable, cost-effective whole-home cooling. Operates at 100% full capacity on demand. Excellent for starter homes, budget-conscious replacements, and rental properties with standard ductwork.
15.2 - 16.5 SEER2 Two-Stage
Our most popular installation for Greensburg homes. Runs at low stage (65% capacity) 80% of the summer to extract heavy humidity, switching to high stage only during heatwaves.
17.0 - 20.0+ SEER2 Variable-Speed
The pinnacle of split cooling engineering. Modulates capacity between 25% and 100% in 1% steps. Delivers whisper-quiet library sound, steady temperatures within 0.5°F, and maximum tax savings.
When installing a high-efficiency central air conditioning split system that meets or exceeds CEE Tier standards (16.0+ SEER2 and 12.0+ EER2), Greensburg homeowners qualify for the Federal Section 25C Energy Efficient Home Improvement Tax Credit, providing an immediate dollar-for-dollar tax credit up to $600.
During peak July humidity in Greensburg, a central air conditioner pulls 10 to 20 gallons of water out of indoor air every 24 hours. If an installer simply runs a cheap vinyl tube into a floor drain without safety switches, a clog can flood finished basements or collapse second-floor ceilings.
Prevents sewer gas and negative plenum air pressure from sucking condensate back into the drain pan, ensuring continuous gravity discharge.
Galvanized steel auxiliary catchment pan underneath the cased coil with an independent secondary float sensor for complete ceiling protection.
Where gravity drains are absent, we install commercial-grade automatic condensate pumps with safety cutoff switches and check valves.
Total residential cooling load is divided into sensible heat (the thermal energy measured on a standard thermometer) and latent heat (the hidden heat stored in airborne water vapor). In Greensburg, summer relative humidity routinely reaches 80% to 90%, creating a high latent moisture burden that standard air conditioners struggle to manage.
In hot, arid climates like Arizona, systems operate at a 0.85 to 0.90 SHR (mostly sensible cooling). In Westmoreland County, our engineers select indoor coils and configure blower speeds for a 0.70 to 0.75 SHR. This dedicates 25% to 30% of total cooling capacity directly toward condensing water vapor, ensuring indoor humidity stays in the optimal 45% to 50% comfort range.
When pairing a two-stage or inverter variable-speed condenser with a communicating thermostat, the system features a dedicated dehumidification mode. On muggy 78-degree mornings with high humidity, the blower speed is dialed down to 320 CFM per ton, dropping evaporator coil temperature and wringing out gallons of moisture without overcooling living areas.
From historic homes along North Main Street to modern suburban layouts in Hempfield Township, our installations are engineered around local architectural realities.
2-Story Brick & Victorian Homes
Solving the severe second-floor heat stack effect. We install high-static ECM air delivery, custom branch dampers, and recommend two-stage or inverter cooling that runs continuously at low speed.
Multi-Level Split-Level Homes
Managing long horizontal duct runs across finished basements. We re-engineer supply trunk transitions to eliminate static pressure bottlenecks and deliver balanced CFM to far bedrooms.
Ranch & Suburban Developments
Addressing unconditioned attic duct runs. We seal all duct joints with fiber-reinforced mastic, verify R-8 insulation wrap, and install secondary emergency drain pans with dual Safe-T-Switches.
Post-War Masonry Homes
Counteracting afternoon masonry thermal storage. We size matched two-stage central AC units that maintain extended low-speed cooling cycles well into humid summer evenings.
We operate with complete financial integrity. Before any work begins, you receive an itemized, guaranteed flat-rate proposal with zero hidden fees, zero travel surcharges, and no surprise changes.
| Installation Scope | What is Included | Estimated Cost | Warranty Coverage |
|---|---|---|---|
| Essential 13.4-14.3 SEER2 Split System | Outdoor condenser, cased A-coil, pad, disconnect, nitrogen brazing, 500-micron vacuum, permits | $4,800 - $6,500 | 10-Yr Parts / 1-Yr Labor |
| Enhanced 15.2-16.5 SEER2 Two-Stage Split | Two-stage condenser, matched cased coil, custom sheet metal plenum, Safe-T-Switch, smart thermostat | $6,800 - $8,800 | 10-Yr Parts / 2-Yr Labor |
| Inverter 17.0-20.0+ SEER2 Variable-Speed | Variable inverter, matched coil, sound blanket, custom transitions, AHRI tax documentation ($600 credit) | $9,000 - $11,500 | 10-Yr Parts / 2-Yr Labor |
| Furnace Add-On Central AC Package | Cased coil atop existing furnace, outdoor condenser, rim joist lineset run, 240V whip, C-wire wiring | $5,200 - $7,800 | 10-Yr Parts / 1-Yr Labor |
| Custom Sheet Metal Plenum Transition | Galvanized steel custom transition fabricated to match furnace cabinet with radius elbows | $350 - $750 | Lifetime Workmanship |
| Dedicated 240V Electrical Circuit Run | New dual-pole breaker, conduit run to exterior wall, weatherproof fused disconnect box | $450 - $850 | Code Compliance Guaranteed |
Read what your neighbors throughout Academy Hill, Fort Allen, and Saybrook Village have to say about our precision engineering and clean installation crews.
"We had an old gas furnace and no air conditioning in our 1920s Academy Hill home. The team designed a custom sheet metal transition, mounted the cased coil perfectly, and routed the copper lines neatly through the basement. They flowed nitrogen while brazing and showed me the 450-micron vacuum reading before charging. Our home has never been this cool and comfortable!"
"Replaced our 20-year-old noisy air conditioner with their Enhanced 16 SEER2 two-stage system in Fort Allen. The difference in sound is incredible, you can barely hear the outdoor unit running from 10 feet away. Best of all, the upstairs bedrooms stay at exactly 71 degrees all night long without any temperature swings."
"Our split-level in Saybrook Village had chronic airflow problems. Other contractors just wanted to sell us a 4-ton unit. This team actually performed a Manual J load calculation, proved a 3-ton variable-speed inverter was the correct size, and balanced our duct dampers. Our electric bill dropped by $90 last month, and we got the $600 tax credit."
Detailed engineering answers to the most common questions regarding central split cooling installations.
Book a no-obligation in-home engineering consultation. Our certified technicians will evaluate your existing ductwork, perform an ACCA Manual J sizing audit, and provide transparent flat-rate options.
Greensburg Heating & Cooling140 S Pennsylvania Ave, Greensburg, PA 15601
Installation Consultation Desk:(724) 482-3710
Consultation Hours:Monday - Saturday: 7:00 AM - 7:00 PM
Emergency Services: 24/7/365 On-Call
Every split-system central air conditioning installation performed by our team includes all required Westmoreland County mechanical and electrical permits. We schedule and coordinate official local building code inspections, ensuring your new residential cooling equipment meets all Pennsylvania Uniform Construction Code (UCC) setback, sound level, and electrical disconnect safety standards.